Komatsu Rasor 4x8 Owners:
3 Special Deals for You
Now is the time to take advantage of special deals on these machines
We now have 3 types of machines available that will
help you to improve your business
If you haven't already upgraded to the Windows version
of
Rasor Server,
each of these machines can be packaged with the new
Rasor Server,
Rasor Nest, and
PathMaster
software.
Below, see why you should buy one of these machines. Then
request a quote by e-mail to
sales@komatsuplasma.com
or call 800-707-2767.
|
Rebuilt and Recertified Rasor KCR-0448 40 Amp, 4 x 8
|
-
Double production capacity
-
No learning curve
-
Reduce maintenance downtime
-
Improve work flow
Double your production capacity by buying an additional
Rasor KCR-0448. It is a very similar machine to the one
you already have,
so you already have the ability and experience in house
to use this machine. The second machine protects against
downtime for maintenance.
Work flow can be increased by
leaving one set up for your most common material, while
using the other for less commonly used materials, or smaller
batches.
|
Refurbished KCR-0448 4x8 40 Amp
|
Rebuilt and Recertified Rasor KCR-0951 90 Amp, 5 x 10
|
-
More than double production capacity
-
or Upgrade to increase production capacity
-
Larger table size
-
More power, 90 Amp
-
Cut thicker materials
-
Cut current materials faster
-
Improve work flow
-
Easy to learn
|
Refurbished KCR-0951 5x10 90 Amp
|
Either add this machine to your current equipment
or replace your existing KCR-0448 to increase your
production capacity. The larger table size means
larger parts can be cut. Larger stock sizes usually
mean increased nesting efficiency, less scrap.
When using smaller stock, perhaps multiple materials
will fit on the table, decreasing loading and unloading
time.
The machine has similar operator controls to the
KCR-0448 you already have, so it will be easy to learn.
The increased power to 90 amp
means that thicker materials can be cut, and your
current materials can be cut faster.
This machine can also be upgraded to a G9120 120 amp
plasma unit, to enable cutting even thicker material,
and other materials at even faster speeds.
|
New Technology Twister 150 Amp, 5 x 10
|
-
Latest Komatsu Plasma Technology
-
More power, 150 Amp
-
Faster cutting speeds
-
Push Pull exhaust
-
Improved cut quality
-
Improved hole cutting
-
Greatly reduced dross
-
Reduce production time
-
Reduce production cost
-
Anti spatter shield
|
New TFP3051 5x10 150 Amp (30 kW)
|
The
TFP3051
features a 5 ft. by 10 ft. cutting
surface and the Twister 30 kW (150 Amp) Fine Plasma
torch. It will cut Mild Steel up to 1" thick,
Aluminum up to 5/8", and Stainless Steel up to 3/4".
It includes the QuickSilver process that produces
superior cutting speeds and edge quality when cutting
Stainless Steel. Cutting speeds are improved and dross
is reduced due to
the high power plasma unit and high speed Twister
gas. Pierce times are reduced due to incorporating
automatic gas change during the touch sensor cycle.
Cut quality is improved by control of main gas flow
and arc mode based on hole size. Spraying anti-spatter
directly through the torch improves hole cut quality
and consumables life. The push-pull zoned exhaust system
greatly reduces fumes while cutting. A mechanical
spatter splash shield is activated during piercing.
The February 2007 issue of FFJournal has an article titled
"Winds of Change, A new kind of twister hits Hickey Metal Fabrication".
This article describes Hickey Metal Fabrication's
experience with the
Twister TFP3051
Order the
TFP3051 with the High Body Factory Installed Option
to increase the Z-Axis stroke from 5 in. to about 12 in.
This allows cutting of square pipe and other structural members
without decreasing accuracy when cutting sheet metal and plate.
To request more information or a quote, send e-mail to
sales@komatsuplasma.com
or call 800-707-2767.
|
